- 1、本文档共21页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
学 号14092000033
毕业设计
题目:
作 者 秦亚红 届 别 2013 届
院 别 机械工程学院 专 业 材料成型及控制工程
指导教师 职 称 教 授
完成时间 2012年5月12日
Effect of Fe and Mn additions on microstructure and wear properties of spray-deposited Al–20Si alloy
Feng Wang*, Zhengye Zhang, Yajun Ma, Yuansheng Jin
Received 8 September 2003; received in revised form 23 February 2004; accepted 27 February 2004
Available online 20 April 2004
Abstract
In this study, the hypereutectic Al–Si alloys were synthesized by spray atomization and deposition technique. The microstructures of spray-deposited alloys were studied using scanning electron microscopy (SEM) and X-ray diffraction (XRD). The dry sliding wear behavior of the alloys was investigated under the applied load of 8.9–35.6 N. The wear behavior of the alloys was dependent on the morphology of the intermetallics in microstructure and applied load. At lower load (8.9 and 17.8N), the Fe-containing alloy showed higher wear rate compared with the binary alloy due to the tendency for embrittlement brought about by needle-like intermetallics. At higher load (35.6 N), Fe- and Mn containing alloy exhibited inferior wear resistance than the binary alloy due to the fragmentation of the intermetallics, thus leading to easier crack nucleation and propagation.
D 2004 Elsevier B.V. All rights reserved.
Keywords: Microstructure; Dry sliding wear behavior; Spray deposition; Wear mechanism
1. Introduction
Al–Si-based alloys have been investigated for automotive applications because of attractive combinations of low coefficient of thermal expansion (CTE), high modulus,excellent wear resistance and good thermal stability [1,2].High Si content in Al–Si alloys usually leads to the formation of coarse Si phase under slow solid
您可能关注的文档
- 毕业论文-大桥维修技术外文文献翻译.doc
- 毕业论文文献翻译--危机管理,孟买发生的恐怖袭击案例研究.doc
- 毕业设计 自动装配设计.doc
- 毕业设计LED显示-基于单片机的交通信息显示系统设计.doc
- 毕业设计plc英文文献翻译-可编程控制器技术讨论与未来发展.doc
- 毕业设计--超临界锅炉设计(淮南煤义马煤对掺混煤)及其过热系统阻力计算.doc
- 毕业设计电气工程及其自动化专业外文翻译--潮流不同排序方案的比较.doc
- 毕业设计开题报告 中心医院住院部大楼设计.doc
- 毕业设计--秦皇岛市汇英中学教学楼+外文文献翻译.doc
- 毕业设计--山岭重丘区县级公路越岭线设计.doc
- GB/T 40096.6-2024就地化继电保护装置技术规范 第6部分:母线保护.pdf
- 《GB/T 40096.6-2024就地化继电保护装置技术规范 第6部分:母线保护》.pdf
- GB/T 43980-2024口译服务 医疗口译要求.pdf
- 中国国家标准 GB/T 43980-2024口译服务 医疗口译要求.pdf
- 《GB/T 43980-2024口译服务 医疗口译要求》.pdf
- GB/T 17215.301-2024电测量设备(交流) 特殊要求 第1部分:多功能电能表.pdf
- 《GB/T 17215.301-2024电测量设备(交流) 特殊要求 第1部分:多功能电能表》.pdf
- 中国国家标准 GB/T 17215.301-2024电测量设备(交流) 特殊要求 第1部分:多功能电能表.pdf
- 中国国家标准 GB/Z 43973-2024非介入式负荷监测(NILM)系统用感知装置.pdf
- GB/Z 43973-2024非介入式负荷监测(NILM)系统用感知装置.pdf
文档评论(0)