- 1、本文档共28页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
专用夹具机构设计及工作过程毕业设计论文文档
【摘要】
本论文主要阐述的零件是CA6140卧式车床上的法兰盘,它位于车床丝杆的末端,主要作用是标明刻度,实现纵向进给。经过查阅资料,首先要对零件进行工艺分析,经过工艺分析,对工序进行对比,通过选定某一工序设计专用夹具,选择定位基准,定位方法和定位原件,进行定位误差分析。
在文档中的一部分,主要叙述了专用夹具设计基本要求和特点,对零件的工艺分析,完成了工艺方案的选定,第二部分,对夹具设计,对夹具设计的计算。最后对主要零部件的设计和标准件的选择,以及对装配图各尺寸提供依据。通过前面的设计方案画出模具各零件图和装配图。
本次设计阐述了专用夹具机构设计及工作过程。本夹具性能可靠,运行平稳,提高生产效率,降低劳动成本和生产成。
关键词:夹具设计 基本要求 工艺分析
【Abstract】
This paper mainly expounds the part is a flange on the end of CA6140 horizontal lathe, which is located in the lathe wire rod, the main role is to indicate the scale, realize longitudinal feeding. Through access to information, the first part to process analysis, through process analysis, comparing the process, by choosing a process special jig design, selection of locating datum, positioning method and positioning of the original, positioning error analysis.
A part of the documentation for the special fixture design, mainly describes the basic requirements and characteristics, analysis of the parts of the process, completed the selection, process scheme of second part, fixture design, the calculation of fixture design. Finally, the design and standards on the main parts selection, and provide the basis for the size of the assembly drawing. Through the front of the design to draw the mold parts drawing and assembly drawing.
The design describes the design and the working process of special fixture mechanism. The clamp reliable performance, smooth operation, improve production efficiency, reduce labor costs and production cost.
Key words: The basic requirements of fixture design process analysis
目 录
3.4.7 钻 4×φ9孔........................................................18
3.4.8 磨削外圆.............................................................18
4.夹具设计.....................................................................19
4.1 设计时注意的问题.......................................................19
4.2 夹具设计...............................................................19
4.2.1 定位基准的选择..............................
您可能关注的文档
- 息烽县龙泉大道软基换填施工方案教案.doc
- 135-热能与动力工程专业卓越工程师培养计划说明.doc
- 情境三-带你了解老年人——老年人的一般心理特征教案.ppt
- 截污排污(沉井)施工组织设计教案.doc
- 2009 SLICC修改的ACR系统性红斑狼疮分类标准.doc.doc
- 戴南新源环保有限公司厂房设计本科毕业设计说明书(论文)教案.doc
- 感应式IC卡-医院门禁一卡通系统方案方案计划书教案.doc
- 2011年嘉兴港区市政道路保洁工程技术标.doc.doc
- 成都理工大学_机械专业_湖北东风汽车_实习报告教案.doc
- 2011高中英语 完形填空精析精练专题二 夹叙夹议完形填空解题指导与训练2(教师版).doc
文档评论(0)