KAA31474AAB-STM-NGSOK2门机资料.doc

下载文档

440
0
约8.67万字
约 68页
2016-05-20 发布于四川
举报
版权申诉
保障服务

KAA31474AAB-STM-NGSOK2门机资料.doc

1、本文档共68页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。

Copyright 2012, OTIS Elevator Co. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of OTIS. Table of Contents 1 Introduction 4 1.1 Power On 5 1.2 Key Function Description 5 2 Software Overview 7 2.1 Local and Remote Service tool 7 2.1.1 Local SVT connection 7 2.1.2 Remote SVT connection 7 2.2 Menu Overview 8 2.2.1 Monitoring Functions (M-3-1) 9 2.2.2 Test Functions (M-3-2) 9 2.2.3 Setup (M-3-3) 9 2.2.4 Run (M-3-4) 9 2.2.5 Engineering (M-3-5) 10 2.3 Key-Function Overview 10 2.4 Access restriction for SVT Menu 10 2.4.1 Require SVC mode to access menu 12 2.4.2 Remote SVT inaccessible Menu 12 3 Function Menus 14 3.1 Monitoring Functions (M-3-1) 14 3.1.1 Status (M-3-1-1) 15 3.1.2 Input (M-3-1-2) 17 3.1.3 Output (M-3-1-3) 19 3.1.4 Runs: Run Time display (M-3-1-4) 20 3.1.5 Part: Display Software Version (M-3-1-5) 20 3.1.6 SysConfig (M-3-1-6) 21 3.1.7 Statistics (M-3-1-7) 23 3.2 TEST (M-3-2) 24 3.2.1 Event log (M-3-2-1) 24 3.2.2 History log (M-3-2-2) 24 3.2.3 Clear log (M-3-2-3) 26 3.3 Setup (M-3-3) 27 3.3.1 Inst: Installation (M-3-3-1) 27 3.3.1.1 ConfigOperator (M-3-3-1-1) 27 3.3.1.2 Learn-run (M-3-3-1-2) 29 3.3.1.3 Mass: Moving Mass input (M-3-3-1-3) 32 3.3.2 DoorTim: Adjust Door Time (M-3-3-2) 33 3.3.3 Def.: Set Default (M-3-3-4) 35 3.3.4 InfChk: Interface check (M-3-3-5) 37 3.3.5 System Reset (M-3-3-6) 38 3.3.6 Parameters (M-3-3-7) 39 3.3.6.1 PROF1: Profile 1 parameter setup (M-3-3-7-1) 39 3.3.6.2 PROF2: Profile 2 parameter setup (M-3-3-7-2) 40 3.3.6.3 SYSTM: System Parameter setup (M-3-3-7-3) 40 3.3.6.4 CNTRL: Control Parameter setup (M-3-3-7-4) 40 3.3.6.5 SELECT: Profile Select (M-3-3-7-5) 40 3.3.6.6 PROF3: Profile 3 parameter setup (M-3-3-7-6) 41 3.3.6.7 PROF4: Profile 4 parameter setup (M-3-3-7-7) 41 3.3.6.8 FIRPRF: Fireman SVC Phase 2 Profile parameter setup (M-3-3-7-8) 41 3.4 Run (M-3-4) 42 3.4.1 Single: Single Door run (M-3-4-1) 42 3.4.2 Cont.: Cycle door run (M-3-4-2) 43 3.4.3 Off (M-3-4-3)